How to Disable 5 GHz on an Edimax Router for Compatibility
Some older wireless devices work reliably on 2.4 GHz but fail to find, join or retain a connection to a 5 GHz network. This can affect older laptops, budget smart-home products, wireless printers, security cameras and appliances that were designed before dual-band Wi-Fi became common. If those devices are important in your home, disabling the 5 GHz radio on an Edimax router can provide a simpler connection environment.
The change is made through the Edimax administration page, usually by opening a local address such as 192.168.2.1 or 192.168.1.1 in a browser. The exact menu names vary between Edimax models and firmware versions, so the wireless settings may appear under Basic, Wireless, 2.4G, 5G or Advanced Configuration.
Turning off one band does not change your internet plan. Your NBN connection, modem, fibre service or mobile broadband link continues to operate as before. It changes the wireless signal produced inside the property, which can be useful in a Sydney apartment, a Melbourne terrace or any home where a particular device needs a less complicated network.
Before saving the setting, record the current wireless name and password. A small amount of preparation also helps you avoid locking yourself out of the router or disconnecting a device that depends on the faster band.
Why 2.4 GHz Can Improve Device Compatibility
The 2.4 GHz band has been used in Wi-Fi equipment for many years. Older wireless adapters and low-cost internet-of-things products often support 802.11b/g/n on 2.4 GHz but have no 5 GHz hardware. Some devices technically support both bands yet struggle when a router presents a shared network name and automatically steers clients between frequencies.
A 2.4 GHz signal usually travels farther through walls and floors than 5 GHz. Its lower frequency can be useful in a brick home in Brisbane or a larger suburban property in Perth, although the band may have more interference. Microwave ovens, Bluetooth equipment, neighbouring routers and cordless devices can all contribute to congestion.
The aim is compatibility rather than maximum speed. 5 GHz generally provides higher throughput and can be cleaner in a crowded area, while 2.4 GHz normally gives older equipment a broader choice of supported channels. If your only problem is one smart plug or printer, disabling 5 GHz may be unnecessary; creating separate wireless names can solve the issue while keeping faster service available for newer devices.
Check the Edimax Model and Current Connections
Look at the label on the router or extender before changing anything. The model number may be printed underneath the unit, beside the serial number or on the original packaging. Edimax interfaces differ across products such as wireless routers, gateway routers and access points, and a setting available on an AC-series model may be absent from an older N-series device.
Connect a computer or phone to the Edimax network before opening the setup page. A wired Ethernet connection is preferable when available because it will remain active if the wireless radio restarts. If you are using an NBN provider such as Telstra, Optus or Aussie Broadband, identify whether the Edimax unit is the main router or an access point connected behind an ISP modem.
Details to Record Before Editing Wireless Settings
- The Edimax model number and hardware or firmware version
- The current network name, wireless password and security mode
- The router address shown as the default gateway on your device
- Any cameras, printers, sensors or appliances currently using 5 GHz
- A spare Ethernet cable and a device with a working web browser
If the Edimax is operating in access-point mode, its management address may have been assigned by the primary modem rather than using the usual default IP. Check the client list in the main modem, or use the Edimax discovery utility if your model includes one. Avoid pressing the reset button at this stage, because a factory reset removes internet, wireless and access-point settings.
Open the Edimax Setup Page
Open a browser while connected to the Edimax network and enter the gateway address in the address bar, not in a search field. Common Edimax addresses include http://192.168.2.1 and http://192.168.1.1, but the correct address is the one assigned to your local network. On Windows, run ipconfig and read the Default Gateway value. On macOS, inspect the connected network under System Settings, and on many phones the gateway appears in the Wi-Fi network details.
Sign in with the administrator credentials. Older Edimax routers may have credentials printed on a label or supplied in the manual, while a previously configured unit will use the password chosen during setup. The Wi-Fi password and administrator password may be different. If the login page does not load, temporarily disconnect from mobile data, check that you are connected to the Edimax network and try the address with http://.
Once signed in, look for a dashboard or navigation panel. The relevant area might be called Wireless, Wireless Settings, Wi-Fi, Basic Settings or Advanced. Some interfaces show separate tabs for 2.4 GHz and 5 GHz; others list both radios on one screen. Take a screenshot of the existing settings before making changes, particularly if the router is part of a home office or a small business network.
Disable the 5 GHz Wireless Radio
Open the 5 GHz or 5G wireless page and look for a control labelled Enable Wireless, Enable Radio, Wireless On, Radio On or Broadcast Network. Clear the relevant checkbox or select Disable. Do not disable the 2.4 GHz section by mistake. If the interface has separate Save, Apply and Reboot buttons, select Apply first and wait for the router to process the change.
Some Edimax firmware places the control under Advanced Wireless Settings. Other versions provide a wireless schedule instead of a direct radio switch. A schedule can be useful when you need 5 GHz during working hours, but for an older device that must remain compatible all day, choose a permanent disabled state. If there is a separate guest network under 5 GHz, check whether it has its own radio setting.
The router may briefly disconnect wireless clients while it applies the change. Reconnect your phone or laptop to the remaining 2.4 GHz network using the saved password. If both bands previously shared one network name, the name may stay the same; the important change is that the 5 GHz radio is no longer advertising it.
Settings Worth Reviewing on the 2.4 GHz Band
- Use WPA2-Personal or WPA2/WPA3 mixed security when older devices require WPA2
- Select 20 MHz channel width where local interference is heavy
- Leave channel selection on Auto initially, then test channels 1, 6 and 11 if needed
- Keep the wireless network name visible during device installation
- Confirm that wireless isolation is off if a printer or smart device must reach other clients
Apply the settings and allow a minute or two for the router to restart its wireless service. A device that was previously attached to 5 GHz may not reconnect automatically if it remembers a band-specific network entry. Forget the saved Wi-Fi network on that device, scan again and join the 2.4 GHz service from scratch.
Configure a Stable 2.4 GHz Network
A distinct network name can make troubleshooting easier. For example, use a name such as Home-2G rather than leaving identical names on multiple access points. This does not make the wireless signal faster, but it lets you see exactly which band and access point a device is using. Avoid including your surname, street address or unit number in the network name.
Channel selection matters in dense Australian housing. In an apartment near central Sydney or Melbourne, many neighbouring networks may overlap. On 2.4 GHz, channels 1, 6 and 11 are the usual non-overlapping choices when using 20 MHz width. Start with Auto, then use a Wi-Fi analyser to identify the least congested option if connections remain unreliable. The best choice can change during the day.
Use a moderate transmit power where the firmware provides that option. Maximum power is not always better because client devices may transmit back at a weaker level, creating an unbalanced connection. Place the Edimax in an open, central position away from metal cabinets, televisions and large appliances. In a double-storey home, positioning near the stairwell may offer more consistent coverage than hiding the router beside the NBN connection box.
After the band change, test each important device separately. Open a web page on an older laptop, print a document, view a camera stream and operate the relevant smart-home appliance. Check the router's connected-client list to confirm that the device has received an address and is communicating over 2.4 GHz.
Resolve Problems After the Change
If the Edimax setup page becomes unreachable, check the cable or reconnect to the remaining Wi-Fi network. A router may take several minutes to apply settings, especially after a firmware update or a configuration reboot. If the router is connected to an ISP modem, make sure your computer has not automatically switched to the modem's separate Wi-Fi network.
A device may still fail because of security compatibility, band steering information stored in its app or an incorrect password. Remove the old network profile, restart the device and add it again. For smart-home products, put the device into pairing mode before starting setup. Some manufacturers require the phone used for installation to be connected to 2.4 GHz throughout the process.
If internet access works on the Edimax but a local device cannot be reached, inspect client isolation, guest-network assignment and access-control rules. A printer connected to a guest SSID may be blocked from computers on the main SSID. An access point connected to a second router may also create two separate networks with different address ranges.
Common Results and Practical Responses
- The older device cannot see Wi-Fi: check that 2.4 GHz is enabled and the SSID is visible
- The device sees Wi-Fi but rejects the password: re-enter the password and verify the security mode
- Connection drops across the house: move the Edimax, reduce channel width or test another channel
- The router works but local sharing fails: disable client isolation and avoid the guest network
- Wi-Fi returns after reboot: save the configuration and check for a firmware or power issue
Do not reset the router unless you have the ISP connection details and a record of the original configuration. A reset can remove PPPoE credentials, VLAN settings, port forwarding, parental controls and access-point mode. If a reset is unavoidable, download the correct Edimax manual first and keep the NBN modem connected while rebuilding the network.
Keep the Network Secure and Easy to Restore
Disabling 5 GHz is a compatibility adjustment, not a security feature. Use a strong administrator password that is different from the Wi-Fi password, select modern encryption supported by your oldest required device and turn off WPS after installation if your equipment no longer needs it. WPS can simplify pairing, but a permanent PIN-based setup is not necessary for most homes.
Check for firmware updates using the exact Edimax model and Australian hardware version. Firmware intended for another regional version can cause problems with radio settings, channel availability or regulatory operation. Australian wireless equipment must operate within local requirements, so leave the country or region setting configured for Australia rather than selecting another market to expose extra channels.
Save a backup of the working configuration if the Edimax interface provides an export option. Label the file with the model and date, and store it somewhere separate from the router. Keep the written network name, password and management address with your household technology records rather than relying on memory.
If the 2.4 GHz connection remains slow, consider re-enabling 5 GHz later and giving each band a separate name. Newer phones, televisions and laptops can then use 5 GHz while older equipment stays on 2.4 GHz. For now, finish by opening the Edimax wireless page, confirming that the 5 GHz radio shows Disabled, and testing one older device from its normal location.